
Maytag Washer Error Codes
Local technicians with everything needed to fix any appliance issue
- Customer support is available around the clock
- When you repair your appliance, the service call is on us
- Our pricing policy is transparent and affordable
- We service appliances of various brands and models
- Have your unit diagnosed and fixed on the same day
Interesting facts about us
Years of experience combined with top-notch tools allow us to perform repairs of any complexity
- 300+
- Positive reviews on:
47 reviews 345 reviews - 20+
- Years of successful work
- With us, you will receive a comprehensive service that covers everything from repair to installation and maintenance. You can trust our team to get your device back up and running and enjoy the peace of mind of knowing you’re in good hands.
- 30+
- Experienced technicians
- All of our technicians have completed training programs and have vast experience in repairing thousands of faulty appliances. They will offer several options to best suit your needs and budget before completing the task.
Error codes list for Maytag washer
Code Error Solution
5D, Sud, Sd
Too much foam
To fix this issue, use the appropriate detergent for your unit and follow the recommended dosage. If that isn’t the case, ensure the drain hose isn’t twisted or blocked.
F5 E2
Door lock issue
Ensure the door is completely closed and nothing obstructs it. Press the “Pause” or “Cancel” button thrice and the “Power” button once. Ensuring the door is properly secured is important to prevent any water leakage or disruption in the wash cycle.
F8 E1, LF, LO FL
Low water flow
You must ensure that the water is turned on and that the hot and cold water taps are fully open.
F8 E2
Problem with the dispenser system
Just confirm the detergent drawer or detergent cartridge isn’t blocked with detergent. A clean detergent dispenser ensures that your clothes get the right amount of detergent for a thorough cleaning.
F9 E1
The drain time is exceeding expectations
First, ensure that the drain pipe isn’t twisted or blocked. Use a U-shaped drain hose. The minimum and maximum height of the pipe is limited to 39″ (99 cm) and 96″ (244 cm), respectively.
F21
Not draining
Start by inspecting the drainage hose, as it could be obstructed. Any blockages found should be promptly removed. There might also be a clog in the drain pump, which needs to be examined and cleared. If the issue occurs again, call a trained technician.
To do this, you need to contact us (866) 905-3275 Or fill out the form and we will contact you as soon as possible book online
F34, rL
Some item was detected in the drum
Remove items from the drum and restart the Clean Washer cycle. It’s important to ensure that the drum is free of foreign objects before starting a wash cycle.
dET
The detergent cartridge not detected in the dispenser
Ensure the dispenser cartridge is inserted correctly and the dispenser drawer is shut completely. Proper placement of the detergent cartridge ensures that your clothes get the right amount of detergent for a thorough clean.
HC
Improperly installed hot and cold inlet hoses
Switch off the water supply, and swap the hoses. Run another cycle to confirm that the hoses are installed correctly.
Int
The cycle was halted
Just press the pause or cancel button twice and the power button once. If that doesn’t work, unplug your unit or disconnect the power for approximately 60 seconds.
LdL
The lid does not secure
Something in your load might be stopping the lid from securing. Have a quick look for any objects right under the lid. Also, check for any detergent accumulation around the lid’s latch mechanism.
lid
Open lid
Just shutting the lid should clear the display. However, please remember that if the lid remains open for more than 10 minutes, the cycle will reset as a safety precaution, and any water inside the drum will drain.
LOC or LC
The control Lock is on
To fix this issue, you should touch the Control Lock button. Some models need you to press and hold the button.
OL
The laundry load was too bulky
You can address this issue by removing several items from the load to reduce its size. After that, close the lid securely and press the START/PAUSE button to restart the cycle.
PF
The power was interrupted during the washing cycle.
To restart the washing cycle, press and hold the START button. Then, you will need to press the POWER button. Power interruptions can disrupt the wash cycle, so it’s important to ensure that your appliance is connected to a reliable power source.
Why choose our team to fix your Maytag washer?
From repairs to maintenance, we’ve got you covered
- Highly skilled technicians
- Use of original spare parts
- Fast same-day service
- Affordable pricing policy
- Professional approach
- Extensive work experience
- 24/7 customer support
- Discounts for loyal customers
- Warranty on repairs and parts
- Residential and commercial services

Areas we service in Canada
Some Areas We Serve

find your location Enter your postal code to find service near you: